CHRYSLER Diagnostic Software Update 2011

CHRYSLER Diagnostic Software Update 2011

CHRYSLER Diagnostic Software for X-431 Product Family V27.60 | 2011-12-20
Compared with the previous version (V27.51), the following have been added:
1. For CAN protocol, the following contents have been added:
1) For PCM: ESIM Forced Monitor Test, O2 Heater System Test, Injector Kill System Test, Compression Test, Cylinder Fuel Quantity Correction Testl, Set RPM Test, Cylinder Balance Test.
2) For BCM: Actuate Engine Battery Feed, Actuate Fuel Pump, Rear Stop and Turn Lamp System Test.
2. The text libraries in Chinese, German, French, Korean, and Italian have been improved.
3. The connector prompting message has been added.

CHRYSLER Diagnostic Software for X-431 Product Family V27.51 | 2011-11-23
Compared with the previous version (V27.50), the following have been added:
1. For Non-CAN protocol, the following special functions have been added for HVAC: Enable Ambient Temp Sensor, Disable Ambient Temp Sensor.
2. For CAN protocol, the following system test menu has been added:
1) HVAC system: Cool Down Test, Actuator Calibration Test, ‘HVAC Self Test;
2) AMP system: AMP Tone Test, AMP Output Channel Test, Speaker Channel Isolation Test, AMP Input Test, AMP Software Test;
3) BCM system systematic test items: View Remote Start Enable Data, View Remote Start Abort Data, View Remote Start Inhibit Data,
3. For Non-CAN protocol, data stream and actuation test items have been improved for each sub-mode of ABS, BCM and HVAC systems
4. The text libraries in German, French and Chinese have been updated.

CHRYSLER Diagnostic Software for X-431 Product Family V27.50 | 2011-10-27
Compared with the previous version (V27.41), the following have been added for CAN protocol:
1. For CAN protocol, PSDML, PSDMR, DVD, AMP systems have been added with RESET ECU function; CCN system has been added with Turn by Turn Navigation function.
2. For Non-CAN protocol, the following special functions have been added for BCM: Reset Module, Reset Learned Features, Reset Customer Preferences, Change Country Code, Double Door Unlock, Rolling Door Locks, Optical Horn Chirp, Auto Door Unlock, Headlamp Delay Time, DRL Enable, Radio EQ Setting, Disable Disarm Switches, Horn Chirp, RKE Unlock Sequence, Program Tire Size, Enable VTSS, Program RKE,RKE Horn Chirp, Disable EU DRL, Auto Door Lock, Enable Immobilizer, Init Learned Features, Initialize VIN, Headlamp On W/Wipers, Enable Fleet DRL.
3. For Non-CAN protocol, the special function Bleed Brake has been added for one sub-mode of ABS system
4. For Non-CAN protocol, actuation test has been added for RADIO system.
5. For CAN protocol, HVAC configuration info content has been improved.
6. The text libraries in German, Italian and Chinese have been improved.

CHRYSLER Diagnostic Software for X-431 Product Family V27.41 | 2011-09-28
Compared with the previous version (V27.40), the following have been added for CAN protocol:
1. For Non-CAN protocol, system scanning function has been added.
2. For CAN protocol, system scanning function has been optimized.
3. For Non-CAN protocol, Quick test function has been optimized.
4. For CAN protocol, data stream and actuation test have revised and improved.
5. For CAN protocol, the problem action of actuation test can’t be continuously tested has been revised and the clear DTC function for TCS and SRS systems has been improved.
6. For NGC protocol, several data stream command has been revised.
7. The text libraries in German and Chinese have been improved.

CHRYSLER Diagnostic Software for X-431 Product Family V27.40 | 2011-09-14
Compared with the previous version (V27.31), the following have been added for CAN protocol:
1. For CAN protocol, Reset ECU function has been added for PTS, PTIM, and RADIO systems; Service Mode, Enable/Disable Front Seat Video functions have been added for RADIO system.
2. The ShortTest function has been added.
3. The text libraries in English and Chinese have been improved.

CHRYSLER Diagnostic Software for X-431 Product Family V27.31 | 2011-08-18
Compared with the previous version (V27.30), the following have been added for CAN protocol:
1. For CAN protocol, the following special functions have been added for ACC system Sub-mode: Align ACC Sensor, Clear ACC Cut Out Events, Reset ECU, Change Cruise Control Mode.
2. For Non-CAN protocol, the special function Disable In Plant Mode has been added to APM system; the special function Radio Clock Display has been added to RADIO system; Reset Module function has been added to DAA, HFM, RPSDM, LPSDM, OCM, PAM, PLGM, SAR and SKM system; View SKREEM VIN function has been added to SKM system.
3. The user information feedback Menu has been added for CAN and Non-CAN Menu.
4. The text libraries in Chinese, French, Korean, German, Arabic, and Italian have been improved.

CHRYSLER Diagnostic Software for X-431 Product Family V27.30 | 2011-08-05
Compared with the previous version (V27.23),
1. For CAN protocol, the following special functions have been added for BCM system Sub-mode: Change Country Code, Sound Horn On Lock, Headlamps On with wipers, Trailer Tow Relay Outputs, Enable DRL, ECU Reset, Auto Wipers.
2. Data stream for Chrysler 6pin connector engine has been and improved.
3. The text libraries in Chinese, French, Korean, German, Arabic, and Italian have been updated.

CHRYSLER Diagnostic Software for X-431 Product Family V27.23 | 2011-07-12
Compared with the previous version (V27.22), the following have been added for CAN protocol:
1. Six special functions have been added for BCM system: Temporary Tip Start Disable, Enable Front Fog Lamp Output, Disable Radio Clock Display, Headlamps Delay Time, Program Network Configuration, and Add Navigation Radio.
2. The text libraries in Chinese, French, Korean, German, Arabic, and Italian have been updated.

CHRYSLER Diagnostic Software for X-431 Product Family V27.22 | 2011-07-08
Compared with the previous version (V27.21), the following have been added for CAN protocol:
1. Four special functions have been added for TCM system: Quick Learn; Clear Variable line pressure (VLP) counters; Reset Learned Adaptives; Store Learned Adaptives.
2. Two special functions have been added for SRS system: Initialize ORC; Rollover Detection.
3. The text libraries in Chinese, French, Korean, German, Arabic, and Italian have been updated.

CHRYSLER Diagnostic Software for X-431 Product Family V27.21 | 2011-06-23
This software is issued in 1 language: English.
Compared with the previous version (V27.20), This update only applies to ISO D sold in Japan.

CHRYSLER Diagnostic Program for X-431 Product Family V27.20 | 2011-06-03
Compared with the previous version (V27.11), the following have been added:
1. For CAN protocol,
1) Five special function codes have been added for PTCM system: Reset ECU, Reset Power Top Control Module, Manual Top Movement, Right Rear window movement and Left Rear window movement.
2) One special function code has been added for PEM system: Reset ECU.
3) Six special function codes have been added for TPMS system: Reset ECU, Program Left Front Tire Sensor ID, Program Right Rear Tire Sensor ID, Program Left Rear Tire Sensor ID, Program Right Front Tire Sensor ID, and TPM Sensor Test.
4) One special function code has been added for SCM and SAS system: Reset ECU.
5) The Reset ECU and actuation test (special functions) have been added for AHBM system.
6) For the models before 2007, the auto searching function of CAN protocol has been added.
2. The text libraries in Korean, German, French and Italian for version V27.11 have been improved.

CHRYSLER Diagnostic Program for X-431 Product Family V27.11 | 2011-05-04
Compared with the previous version (V27.10),
1. The system structure has been optimized (menu structure has been revised).
2. For CAN protocol, the PTCM, PEM, and TPMS systems have been added with the diagnostic functions of read DTCs, clear DTCs, read data streams, read version information, and read configuration.

CHRYSLER Diagnostic Program for X-431 Product Family V27.10 | 2011-03-30
Compared with the previous version (V27.05), the text library in Korean has been updated.

CHRYSLER Diagnostic Program for X-431 Product Family V27.05 | 2011-03-08
Compared with the previous version (V27.00),
1. The program in Italian has been issued:
2. The text libraries in simplified Chinese, traditional Chinese, French, German have been updated and improved:

CHRYSLER Diagnostic Program for X-431 Product Family V27.00 | 2011-02-23
Compared with the previous version,
1. The following systems under CAN protocol have been added:
SAS, ITM, LRSM, MSMD, PLGM, LPSDM, RPSDM, PTIM, SDAR, SDARV, SUNR, TM, VES, VES3, and SCM
2. For following systems under CAN protocol, the actuation test function has been added:
WCM, DMFR, and ABS
3. The system scan function has been added for CAN menu, which can automatically scan the vehicle model and the related existing systems.
4. For following systems under CAN protocol, the special functions have been added:
(1) PCM: RELEARN CAM/CRANK, LEARN ETC, and Quick Learn, etc. (for mode 6)
(2) TCM: Reset ECU (for 6 modes); TCC Break-In (for mode 4); Initialize EGS-52/53 (for mode 5); Initialize CVT (for mode 6); TCC Break-In, Thermistor test, and Overdrive Switch test (for mode 8)
(3) CCN: Unlock Driver Door On 1st Press change Measurement unit, Auto door unlock, Auto door lock, Lauguage preference, Seatbelt system, and Reset ECU, etc., (for mode 2); while for mode 5 and 6, just partial functions have been added.
(4) SRS: Reset ECU (for every mode)
(5) BCM: Horn Chirp Duration (for mode 7, 8); Illuminated Entry Time, Flash Hazard Lamps On Lock, and Accessory Delay Time (for mode 7, 8, 9)
5. For PCM system under CAN protocol, the data stream algorithm of "Engine speed from camshaft sensor" has been revised for mode 5, besides, the actuation test menu has been revised.

This entry was posted in diagun info. Bookmark the permalink.